沟厕女厕所白嫩大屁股-八个少妇沟厕小便各种大屁股-16位女子蹬坑撒尿视频-各类女厕所偷拍大集合

<code id="zuino"><rp id="zuino"></rp></code>
    1. <acronym id="zuino"></acronym>
    2. <acronym id="zuino"><strong id="zuino"></strong></acronym>

        <td id="zuino"></td>
        1. SS-DP_SERIES

          Update:2015/6/12 9:22:50      View:1299
          • Type   
          • Description

            SS-DP_SERIES

          Introduction
           

                    SAFETY INSTRUCTIONS         1.Make sure your battery has enough voltage for the controller to recognize the battery type before first installation.

          2.The battery cable should be as short as possible to minimize loss.

          3.The regulator is only suitable for lead acid batteries: OPEN,AGM, GEL

          it is not suited for nickel metal hydride, lithium ions or other batteries.

          4.The charge regulator is only suitable for regulating solar modules. Never connect another charging source to the charge regulator.

                     PRODUCT FEATURES          

          1.Build-in industrial micro controller.

          2.One-key on/off the output,4-stage battery led indicator.

          3.Fully 4-stage PWM charge management.

          4.Build-in short-circuit protection,open-circuit protection,reverse protection,over-load protection.

          5.Dual mosfet Reverse current protection ,low heat production.

                     SYSTEM CONNECTION        

          1.Connect the battery to the charge regulator - plus and minus.it will show”1” if it detects 12V battery,”2” if it detects 24V battery.

          2.Connect the photovoltaic module to the regulator - plus and minus.

          3. Connect the consumer to the charge regulator - plus and minus.

          The reverse order applies when deinstalling!

          An improper sequence order can damage the controller!

           

                            SETTING                

          Press the button to open or close the load ,the button is useless if the battery is in LVD(low voltage disconnect)mode. The 25% LED will be blinking when in LVD mode.
           

                     TROUBLE SHOOTING         

          Situation

          Probable cause

          Solution

          Charge LED not on when sunny

          Solar panel opened or reversed

          Reconnect

          Load LED off

          Mode setting wrong

          Set again

          Battery low

          recharge

          Load LED slow flashing

          Over load

          Reduce load watt

          Load LED slow flashing

          Short circuit protection

          Auto reconnect

          Power off

          Battery too low/reverse

          Check battery/connection

                   TECHNICAL PARAMETER        

          MODEL/SS

          1250DP

          1260DP

          4850DP

          4860DP

          Batt  voltage

          12V/24V auto

          48V

          Charge current

          50A

          60A

          50A

          60A

          Discharge current

          50A

          60A

          50A

          60A

          Max Solar input

          <50V

          <100V

          Charge drop

          <0.2V

          Discharge drop

          <0.25V

          Equalization

          14.8V

          Bulk

          14.5V

          Acceptance

          14.2V PWM

          Float

          13.8V

          Charge reconnect

          13.0V

          Discharge stop

          11.2V

          Discharge reconnect

          12.6V

          Self-consume

          <10mA

          Voltage of open light

          Solar panel 8Vdelay 10s

          Voltage of close light

          Solar panel 8Vdelay 60s

          Temperature compensation

          N/C

          Operating temperature

          -35~+60 ℃

          Size/Weight

          166*113*355mm /645g

          *all red color voltage X2 while using 24V system

          *Product specifications are subject to change without prior notice

           

          More Products
          沟厕女厕所白嫩大屁股-八个少妇沟厕小便各种大屁股-16位女子蹬坑撒尿视频-各类女厕所偷拍大集合